What did you do in your shed / man cave today?

[Raym]

Good work mate I bet the billy lids love it

[speewa158]

What will I do in the mean time......
  You could always  " Dickabout " As you are 1 of the Best " Dickabouters  " l know  & though its thirsty work     

[glenm64]

Outdoor area cupboards all finished, very happy with the look.





Natural edge came out really good





Got a lower half of a feature wall to do similar, but Im goig to use mini custom orb as infill.

Cheers Glen

[feisty]

Installed two x 2 usb ports into the center console of the Cruiser where the coin holders are. 

Looks good. Never seen these type before.  Where can I get some???

[Rumpig]

Wasn't the man shed, but on the house....removed and replaced the storm water pipes that goes from the house to the water tank. For some reason when i did it originally i put the leaf catcher up under the guttering, which is a right royal pain in the arse to get to and clean out....so today i removed that set up and have dropped it down lower where it is much easier and safer to reach 

[D4D]

We've got some parkland/bush/water across the road from our house. Went for a walk with the young bloke yesterday and noticed there were a few trees across the path, and bark and crap everywhere. Obviously my shire rates don't cover keeping the place tidy. Any excuse to get the chainsaw out so we went to work clearing it up and raked all the paths clean. Young bloke says to me 'this is like where the mountain bike riders ride'. So we 'may' have spent some more time making a single track, berms and ramp for him to ride on

[Champin]

Ripped all me annex poles out and colour coded them with heat shrink. Makes laying them out a whole lot easier. Also pulled out the screws and run a bit of anti sieze over them. With the new hot water shower all hocked up and  batteries charged we're ready to go out again. Happy happy joy joy.

[jmorgan1981]

Outdoor area cupboards all finished, very happy with the look.





Natural edge came out really good





Got a lower half of a feature wall to do similar, but Im goig to use mini custom orb as infill.

Cheers Glen

That looks great.

[Bill]

Very nice job on the outdoor area.
Bill

[Moggy]

You may have been asked & answered but what is the timber glenn? Looks schmicko, love a craftsmans work.

Sent from my SM-G900I using Tapatalk

[DaveR]

That looks the good Glen, nice work. 

[glenm64]

You may have been asked & answered but what is the timber glenn? Looks schmicko, love a craftsmans work.

Sent from my SM-G900I using Tapatalk

River Red Gum finished with Danish Oil.
Cheers fellas for the comments.
Learnt alot doing these, thought they would be tricky, but having to start with the inner edge and working outwards really got the brain going.

Cheers Glen

[Bird]

Fixed up the LED Blinkers (had one with blinker inside not outside), changed boost gauge to 30psi, went to change pillar pod to from 3 to 2 pod, but didn't like it so put the bodged 3 pod back up.

Fitted the rest of the LED lights to roof pod, but they didn't fit ;(

Found globes for the gauges, changed em. Thought about rewinding the winch plasma back on but CBF.. too humid out there for fat ****s now.
Cleaned out car for next weekends Club Driver Training weekend.. My first as a trainer...

Went for test drive to check the lights etc, and happy

[GeoffA]

Found globes for the gauges, changed em......

What kind were they?....

[xcvator]

What kind were they?....

Electric

[plusnq]

Much easier than the gas ones 

[GeoffA]

Electric

Much easier than the gas ones 

You gents make jokes, but ultimately they're actually diesel powered.....

[Bird]

What kind were they?....

took photos of the 15/30 and EGT globes

[xcvator]

You gents make jokes, but ultimately they're actually diesel powered.....

Nah, that's the heater in the Tanami

[GeoffA]

took photos of the 15/30 and EGT globes

...with your 'phone??

[Black Diamond]

Fixed up the LED Blinkers (had one with blinker inside not outside), changed boost gauge to 30psi, went to change pillar pod to from 3 to 2 pod, but didn't like it so put the bodged 3 pod back up.

Fitted the rest of the LED lights to roof pod, but they didn't fit ;(

Found globes for the gauges, changed em. Thought about rewinding the winch plasma back on but CBF.. too humid out there for fat ****s now.
Cleaned out car for next weekends Club Driver Training weekend.. My first as a trainer...

Went for test drive to check the lights etc, and happy

Mine fitted perfectly thanks bud and much brighter then the old ones

[DaveR]

Made myself a trolley for the flash new MIG I got.



Now I know I could have bought 1 for $70, but wots the point of having a flash new MIG if ya aint gonna use it.



It cost me $30 for the 2 main rear 50 kg load wheels and 2 x 1/2" bolts to make the axles with, the rest was lying about in my way.... 

Just got to find some material to close the lower part in to keep welding stuff. No way I'm buying it.
Next, make a bike rack....

[Crisp Image]

Made myself a trolley for the flash new MIG I got.



Now I know I could have bought 1 for $70, but wots the point of having a flash new MIG if ya aint gonna use it.



It cost me $30 for the 2 main rear 50 kg load wheels and 2 x 1/2" bolts to make the axles with, the rest was lying about in my way.... 

Just got to find some material to close the lower part in to keep welding stuff. No way I'm buying it.
Next, make a bike rack....

Ya need to practice a bit more. The top is not level 
Crispy

[DaveR]

Very funny. That's what I'd expect oldmate to say.

Sent from my ZTE T83 using Tapatalk

[Raym]

New exhibition at work. Some of these are up to 90 years old & some proceeds of crime.